Safety-critical systems are well documented and standardized (e.g. IEC 61508, RTCA DO-178B) within system design cycles. However in Defence and Security, systems that are critical to the success of a Mission are not defined within the literature nor are there any guidelines in defining criticality in their design or operational capabilities. When it comes to…

The research reported in this paper proposes an Advanced Process Control system, denoted “i.Process | Steel – RHF”, oriented to energy efficiency improvement in a pusher type billets reheating furnace located in an Italian steel plant. A tailored control method based on a two-layer Model Predictive Control strategy has been created that involves cooperating modules.…

Exploring communities and outliers in Social Network is based on considering of some nodes have overlapped neighbor node within the same group as well as some nodes have no any link to the other node or have no any overlapped value. The existing approaches are based on the overlapping community detection method were only defined…

Mobile broadband has gained momentum with the growing demand of user data rates. Long Term Evolution (LTE) technology is the step in mobile communications evolution, developed to satisfy high data rate demand, and meet better spectral efficiency requirements. Effective radio resource management and inter cell interferences are the major challenges. Fractional Frequency Reuse (FFR) is…

This paper is devoted to the analysis of aircraft dynamics in the cruise flight phase under windshear conditions. The study is conducted with reference to a point-mass aircraft model restricted to move in a vertical plane. We formulate the problem as a differential game against the wind disturbances: The first player, autopilot, manages, via additional…

In this modern age, information technology (IT) plays a role in a number of different fields. And therefore, the role of security is very important to control and assist the flow of activities over the network. Intrusion detection (ID) is a kind of security management system for computers and networks. There are many approaches and…

Detect and tracking of moving weak targets is a complicated dynamic state estimation problem whose difficulty is increased in case of high clutter conditions or low signal to noise ratio (SNR). In this case, the track-before-detect filter (TBDF) that uses unthresholded measurements considers as an effective method for detecting and tracking a single target under…

This paper describes the design and analysis of a regenerative braking system for a permanent magnet synchronous motor (PMSM) drive for electric vehicle (EV) applications. First studied is the principle for electric braking control of a PMSM motor under field-oriented control (FOC). Next, the maximum braking torque in the regeneration mode as well as the…

In recent years, a number of studies have been conducted exploring the potential of digital tour guides, that is, multimedia components (e.g., 2D graphic, 3D models, and sound effects) that can be integrated into digital storytelling with location-based services. This study uses component-based software engineering to develop the content of game-based tourism information services. The…

Examples of analytical calculations of the system characteristics of the hardware and time complexity of the correlation system based on a certain number of microphones and the corresponding number of interrelations are presented. The structural solutions of the hardware special processor implementation of such class of multichannel devices for recognition and identification of types and…

The occurrence of many failures in the power system can lead to power instability and affects the system parameters to go beyond its operating limits. It may lead to obstructing the secure operations and reliability of power systems. Ensuring power system security needs proper actions to be taken for the undesirable contingency. Thus, security analysis…

One of the prominent challenges of the automotive-transportation system is represented by the integration of security and safety properties within protocols, applications and connectivity mechanisms. A joint safety/security design can sometimes expose to trade-offs, since their requirements may not match perfectly or even be incompatible. This paper analyses an example of security and safety design,…

This paper investigates the efficiency benefits of replacing the Silicon diodes of a commercial IGBT module for the main inverter application of an electric vehicle with Silicon Carbide diodes, leaving the package, operating conditions and the system unchanged. This ensures that the comparison is directly between the chip technologies without any scope for discrepancies arising…

This paper, presents the design of a temperature sensor based on RO (Ring Oscillator) in order to make a thermal study for the detection and localization of thermal peaks in a complex system. In this work, a simulation and FPGA implementation of a fully digital temperature sensor features a number of exact inverters that can…

Due to the increasing bandwidth requirement of modern wireless communication systems, developing antenna having wider bandwidth have been receiving significant attention in the recent years. In this paper, a comparative analysis of the contacting feed (micro strip line and coaxial probe) and non-contacting feed mechanism (both Aperture Coupling and Proximity Coupling) in micro strip patch…

The world’s pollution rates have been increasing exponentially due to the many reckless lifestyle practices of human beings as well as their choices of contaminating power sources. Eventually, this lead to a worldwide awareness on the risks of those power sources, and in turn, a movement towards the exploration and deployment of several green technologies…

In this paper, stabilization of uncertain systems was established using zonotopic sets. The obtained state feedback control laws are computed by an off-line approach reducing computational burdens. The resolution of a robust model predictive control (MPC) allows computing a sequence of state feedback control laws corresponding to a sequence of zonotopic invariant sets. The implemented…

Constant Envelope Discrete Cosine Transform based Orthogonal Frequency Division Multiplexing (CE-DCT-OFDM) system with M-ary Pulse Amplitude Modulation (PAM) mapper is considered. In the system phase modulation is used to achieve constant envelope signals that have 0 dB Peak-to-Average-Power Ratio (PAPR). Transmission of such signals permit high power amplifiers in the system to operate with maximum…

This paper presents various concepts related to the application of a microgrid pilot project in a residential condominium at Fortaleza / CE – Brazil, such as battery energy system, renewable and distributed generation, islanding recloser and all different units using interface based on power electronics. This papers main objective is to create information about microgrid…

The key objective of this study is to analyse the heat transfer processes involved in the evaporation and condensation of water in a water distillation system employing a thermoelectric module. This analysis can help to increase the water production and to enhance the system performance. For the analysis, a water distillation unit prototype integrated with…

Through-Silicon-Vias (TSVs) are utilized for high density 3D integration, which induce crosstalk problems and impact signal integrity. This paper focuses on TSV crosstalk characterization in 3D integrated circuits, where several TSV physical and environmental configurations are investigated. In particular, this work shows a detailed study on the influence of signal-ground TSV locations, distances and their…

Microelectromechanical Systems (MEMS) are devices made up of several electrical and mechanical components. They consist of mechanical functions (sensing, thermal, inertial) and electrical functions (switching, decision making) on a single chip made by microfabrication methods. These chips exhibit combined properties of the two functions. The size of system has characteristic dimensions less than 1mm but…

The uncertain nonlinear systems can be modeled with fuzzy differential equations (FDEs) and the solutions of these equations are applied to analyze many engineering problems. However, it is very difficult to obtain solutions of FDEs. In this paper, the solutions of FDEs are approximated by utilizing the fuzzy Sumudu transform (FST) method. Here, the uncertainties…

Quality assurance of modern-day safety-critical systems is continually facing new challenges with the increase in both the level of functionality they provide and their degree of interaction with their environment. We propose a novel selection method for black-box regression testing on the basis of machine learning techniques for increasing testing efficiency. Risk-aware selection decisions are…

Ensuring the compliance of developed software with general and application-specific security requirements is a challenging task due to the lack of automatic and formal means to lead this verification. In this paper, we present our approach that aims at integrating the formal specification and verification of security guidelines in early stages of the development lifecycle…