Search Results

High Intensity Focused Ultrasound (HIFU) was widely used for treating tumors non-invasively. In this treatment, ultrasound is focused on the target volume inside the human body to ablate cancerous tissues and Magnetic Resonance Imaging (MRI) is mainly used to grasp the target position and to measure the temperature distributions around the target. However, MRI is…

Metamaterial antennas are some sort of antennas which utilize metamaterials to improve the efficiency of small (small electrical) antenna systems and also enhance the antenna’s radiation pattern. The unusual properties of metamaterials such as coefficients of permittivity and permeability, as well as the negative refractive index, have led to increase the use of these artificial…

The research reported in this paper proposes an Advanced Process Control system, denoted “i.Process | Steel – RHF”, oriented to energy efficiency improvement in a pusher type billets reheating furnace located in an Italian steel plant. A tailored control method based on a two-layer Model Predictive Control strategy has been created that involves cooperating modules.…

This article describes the modeling procedure of a direct resistive heat model of the molybdenum sheet and its simulation with electrodes made from various materials. The main characteristic of the proposed model is its dynamic behavior, because model considers the movement of the molybdenum sheet. The simulation results are mutually compared and the optimal material…

Sustainable energy is gradually becoming the norm today due to greenhouse warming effects; as a result, the quests for different renewable energy sources such as photovoltaic cells as well as energy efficient electrical appliances are becoming popular. Therefore, this article explores the alternative energy case for thermoelectricity with focus on the steady-state mathematics, mixed modelings…

Office buildings commonly use fully glazed façades to reflect a luxurious appearance and to maximize natural light of high solar exposure and high-energy consumption due to cooling and heating. There is a great abundance in constructing shading screens as they are part of the modern movement in field of Energy Conservation, renewable energies, and architectural…

Radiofrequency catheter ablation is routinely used for the therapy of cardiac arrhythmias. Compared with the traditional unipolar ablation, bipolar ablation may improve the controllability of treatment, and prevent side effects and complications caused by catheter ablation. In addition, the variations of myocardial fat’s thickness and myocardial impedance may have significant influence on the performance of…

Fuel Cells (FCs) and Combined Cooling, Heating and Power (CCHP) systems are becoming very popular due to their environmental friendliness and immense applications. This extended review paper commenced by introducing the rampant South Africa’s electricity crisis as the basis for the study, followed by some structural analyses of up to forty-four miscellaneous power electronics converters…

Fossil fuel can no longer supply the constantly spiking demands of energy around the world, hence the increasing research on renewable energies as an alternative. The Stirling Engine is an external combustion engine, giving us a wide range of heat sources: solar, nuclear. The Stirling engine makes best of use of solar sources in an…

South Africa is aiming to achieve a generation capacity of about 11.4GW through wind energy systems, which will contribute nearly 15.1% of the country’s energy mix by 2030. Wind energy is one of the principal renewable energy determinations by the South African government, owing to affluent heavy winds in vast and remote coastal areas. In…

Biodiesel was produced from lard using a CaO catalyst derived from eggshells. The effects of catalyst loading and transesterification reaction time were investigated. The results revealed that the increase in yield of biodiesel occurred at all catalyst loading when the reaction time was increased. The optimal reaction time was obtained at 60 minutes. The results…

In this study, the ASTM A48 Class 30 gray cast iron was cast in a medium frequency induction furnace. The ultimate tensile strength (UTS), ultimate flexural strength (UFS) and microstructure were determined in accordance with ASTM E8/E 8M-80 and ASTM A438-80 (1997). From the results of this study, the graphite size at overheating temperatures 1350oC…

In order to balance the power in intelligent distribution networks (Smart Grid or Microgrid), it is proposed to organize a «multi operated virtual power plant». The resources of active and reactive power for which can be obtained using an AC voltage controller with a phase-angle control for regulation of operating modes of the ohmic load…

Harmonic distortion is a problem that can be caused by the use of power electronic devices. The effect of harmonics has an impact on changes in the input voltage source waveform which is referred to as wave defects. This incident has an impact on electronic faults and overheating of the power transformer coil as a…

The water heating with parabolic trough solar collectors (PTC) is a very widespread and at the same time quite promising solar technology. However, PTC presents several problems in terms of the profitability of water heating. For this reason, our study of water heating with PTC collectors consists of two main parts. In the first part,…

This paper is a case study of the integration of an energy management system (EMS) in a commercial building. A detailed analysis of this EMS’s impact on energy consumption is presented. High energy demand is very common in commercial and industrial facilities. With this in mind, the present work aims to improve the energy consumption…

Different types of air-to-air energy recovery technologies such as coil loops, heat pipes, sensible wheels, and total energy wheels are frequently incorporated in HVAC systems in an attempt to reduce energy consumption. This study examines the impact of various types of energy recovery technologies and capacity control strategies on a building’s cooling, heating, and fan…

The digital factory is a concept signing a new era for industry, the so-called Industry 4.0, in which ordinary production systems like manufacturing plants, machineries and utilities are being equipped with diagnostic and sensitive instrumentation to be connected to digital shared networks. This data-sharing, trough the big data management techniques, is a fully integrated base…

The purpose of this paper is to improve the thermographic method for detection the places of heat energy losses on the urban underground thermal pipelines using the computer system. This goal was achieved by building a heat map of the surveyed heating main with data layering directly on a computer map of the area, which…

This paper deals about an application of optimal power flows (OPF) constrained with synchronous generator capability curve for power market analysis (SGCC). OPF main features gather in its mathematical formulation non-convexity, non-linearity, and it shows to be a hard to solve optimization problem. In some operational scenarios, SGCC can limit power flows bringing the theoretical…

During microwave heating of materials, the efficiency of microwave heating depends on the materials’ dielectric property, shapes and sizes of the material, materials’ position inside the applicator, operating frequency, level of input power, specific heat capacity, number and position of waveguide over the applicator, size and geometry of applicator etc. This paper examines the effects…

This paper, presents the design of a temperature sensor based on RO (Ring Oscillator) in order to make a thermal study for the detection and localization of thermal peaks in a complex system. In this work, a simulation and FPGA implementation of a fully digital temperature sensor features a number of exact inverters that can…

We describe a mathematical model for the industrial heating and cooling processes of a steel workpiece representing the steering rack of an automobile. The goal of steel heat treating is to provide a hardened surface on critical parts of the workpiece while keeping the rest soft and ductile in order to reduce fatigue. The high…