Search Results

Combinatorial software testing is regarded as a crucial part when it comes to the software development life cycle. However, it would be impractical to exhaustive test highly configurable software due to limited time as well as resources. Moreover, a combinatorial testing strategy would be to employ input-output-based relations (IORs) due to its benefits versus other…

This paper addresses experiments with Scratch-developed games in the robotics introduction course at the Federal University of Technology – Paraná. It aims at assisting learning of classical and initial robotics concepts. This proposal, similar to the classic 80s war tanks game on Atari 2600, was developed using an autonomous vehicle. In the first experiment, applied…

Just as industry is dynamic, constantly evolving according to the state of technology, economics, politics and so on, so must be, higher education. Studies have shown that higher education, for the past century, has constantly adapted to the dynamic skill and knowledge requirements of industry. This adaptation, however, is not always timeous and precise resulting…

This paper makes a statistical analysis of some indicators that characterize the environment of students admitted to public and private Institutions of Higher Education i.e. university level institutions, presenting an overview to the distribution of these students in the key areas of study that these institutions offer such as: Arts, Agriculture, Natural Sciences, Social Sciences,…

Genome-wide association studies, or GWAS, have reported associations between SNPs and specific diseases/traits. GWAS results contain variants located in different genomic regions, including variants in the 3’UTR. MicroRNAs, or miRNAs, are small noncoding RNAs that bind to the 3’UTRs of genes to regulate gene expression. However, variant(s) that are located in the 3’UTR could impact…

This paper studied the influence of using hybrid additives of Nano Clay (NC) and Marble Powder (MP) on the structural behavior of columns, in terms of ultimate capacity, axial strain, lateral strain, toughness, and failure pattern. For this purpose, ten column specimens were made from reinforced concrete (RC), either normal or high strength, and were…

The following document analyzes the current situation in mobility and intelligent transportation in Colombia and in some cities around the world. Presenting several cases of success and implementation of technologies and protocols that seek to improve the problems with the greatest impact in today’s cities, such as traffic congestion, environmental impact, accessibility, and road safety.…

The Present work is to investigate effect of dry sliding wear behaviour of ZA27 base alloy, after reinforcing it with Molybdenum Di Sulphide (MoS2) particles from 0% to 4% in five steps. To examine the wear behaviour of both reinforced and un-reinforced material, dry or unlubricated pin on disc tests were conducted. These tests were…

The effectiveness and suitability for the reliability and test of the embedded software of the automotive EHPS (Electrical Hydraulic Power Steering) pump are extensively explored in this paper. The Crow-AMSAA analysis has been applied to evaluate the embedded software reliability growth based on the failure data collected in the prototype phase and in the field.…

Data mined from social media can be used in a variety of methods. The goal of this paper is to explore some of the various methods of mining data from social media and the different areas of its applications. From the analysis of other studies, it was clear that methods such as text analysis, classification,…

The article further extends the researched issue of the unmanned aircraft use in the pre-flight and post-flight visual check of aircraft. Procedures of pre-flight inspection are fulfilled by the aircraft maintenance certified staff or the crew member before flight. The process is similar for all categories of aircraft, but its implementation differs for individual specific…

A competitive manufacturing environment dictates to be conscious of the real cost of production to increase profitability, to have a precise cost estimation, and to avoid cost distortion. Activity-Based Costing (ABC) is one choice to achieve these objectives. This paper aims to build an ABC method, consequently, to explore its application for a local Aluminum…

In this paper a synchronization methodology of two fractional-order chaotic oscillators under the framework of identical synchronization and master-slave configuration is introduced. The proposed methodology is based on a fractional-order feedback control design under the frame of control theory, the feedback controllers provide synchronization convergence. A comparative study between a proportional control, a nonlinear fractional-order…

Distributed Solar Photovoltaic (DSP) Plants are one of the fastest growing renewable energy systems in South Africa. The primary components forming an integral part of the point of common coupling (PCC) are, the inverter used to convert dc voltage to ac voltage and step-up transformers which step-up low voltage input to the desired output level.…

PT XYZ has an Enterprise Resource Planning application that is used by the Planning Department to view stocks and plan production materials. Currently calculation of production materials takes more than 30 seconds just to export to Excel then a few minutes to adjust the data format to the planning form and the data used is…

This paper is an extended version of the work presented at a conference held in Kyiv, Ukraine, in October 2020, which reported the result of the numeric simulation on the artificial antigravity. This paper further describes the derivation of the idea of the artificial antigravity, and adds the simulation of angular momentum that is needed…

More than one year after the outbreak of the COVID-19 pandemic the behavior of figures published by official sources of the countries are skeptical for the public. Many probability tests are used to detect the reliability of information among which Benford’s Law. This study focused on the Western Balkan countries, as one of the foremost…

In recent days, the fast growth of populations leading to an increase in medically complicated cases, especially fast spread viral cases around the world. These phenomena increased demand on auto-diagnose systems to speed up the diagnosis process and reduce human contacts, especially for the COVID-19 pandemic using deep learning (DL). DL methods can successfully carry…

Formal methods are one of the efficient tools to verify and validate designs for different kinds of systems. Smart systems are attracting researchers’ attention due to the rapid spread of new technologies all over the world. Modeling a smart system requires connecting heterogeneous subsystems together to build it. Our contribution to this work is in…

The Additive Manufacturing (AM) technology is a disruptive and novel technique that changes the paradigm of manufacturing methodology. It is based on the principle of having 3D parts by adding simple 2D layers on and on. Before AM was implemented, the conventional subtractive and chip-away techniques such as milling and turning processes had been used…

Music Emotion Recognition (MER) is a study to recognize emotion in a music or song. MER is still challenging in the music world since recognizing emotion in music is affected by several features; audio is one of them. This paper uses a deep learning approach for MER, specifically Convolutional Neural Network (CNN) and Convolutional Recurrent…

The ecosystems and landscape patterns in Lake Victoria basin are increasingly being modified by changes in land use/land cover. Understanding dynamics of these changes is essential for appropriate planning. This study evaluated changes in landscape environment, of the lakeside counties of the Kenyan Lake Victoria basin, which have occurred over a forty-year period (1978-2018) and…

A Japanese method in teaching at classroom show good result by implementing Kamishibai. On the other hand, technology is inseparable from daily life. Computer-based learning media innovations are fast and diverse, ranging from 2D animation to 3D environments. The hologram is one example of 3D object visualization to deliver the learning material. Based on Kamishibai’s…

The article suggests four circuit topologies for the practical simulation of grounded and floating lossy inductors. All the suggested circuits use commercially available integrated circuit LT1228 chips as active elements, and only two passive elements, namely one resistor and one capacitor. The first two of the proposed circuits employ only a single LT1228 active element…

To this extent, the delineation of techno-economic evaluations for transformers becomes more intricate through a lens of Distributed Solar Photovoltaic (DSPV) market in South Africa. Essentially, the transformer price and loss evaluation techniques should be tailored for calculating the Total Ownership Cost (TOC) of transformers facilitating decentralized energy systems. In South Africa, the traditional coal…